Calibrating the Shinyei PPD Sensors…..Part 2

In Part 1, I covered how I added an air-tight fan (well I have not yet published the mechanical details) to the PPD60PV-T2 and that reduced the variability of the particle count by a large amount.

In this post, I will compare the output of the T2 with and without the fan to the Shinyei AES1 (aka PMS1). The latter is a PM2.5 sensor i.e. gives output in ug/m3. The T2’s output is in volts or pulse occupancy which can be translated into PCS which is particles per 0.01 cu ft.

So I connected the 42 and the T2 to an Arduino Uno and used the interrupt function to measure the low pulse occupancy and the A->D function of the Arduino to measure the analog voltage (only for the T2). Every 30 seconds I printed these measures to the input USB port of a raspberry Pi which then posted to the net. In the case of the T2 with the fan, I built an acrylic case, housed the sensor+air tight fan and sent the data directly to the net using an Arduino Ethernet. The AES-1 has its own Ethernet board which also connected to the net, but then it sent the data only to a Windows computer (I had to borrow one from my Dad as I has not really seen one before).

So, here is the plot of the T2, T2 with Fan, Dylos (ignore for now) and the AES. This was for one day. The vertical axis is really a straight line scaling of the raw output from the T2, except for the Dylos when it is the actual reading of the small particles.

The plots are using which reads the data from TempoDB via a python script.

Shinyei PPD60PV-T2 with and without Fan vs AES-1 every 30 secs

Shinyei PPD60PV-T2 with and without Fan vs AES-1 every 30 secs

And here are the correlation plots, first without the fan.

Shinyei PPD60PV-T2 without fan vs AES-1

Shinyei PPD60PV-T2 without fan vs AES-1

The R2 is 0.57, not too bad but not great. So from here (ignoring the y-intercept), one can take the T2 reading and divide by 27 to get the PM2.5 reading.

But things significantly improve with the T2 and fan.

Shinyei PPD60PV-T2 with fan vs AES-1

Shinyei PPD60PV-T2 with fan vs AES-1

Now the R2 is 0.96! So the simple addition of a fan made the T2 become a much better sensor for measuring PM2.5 by measuring the scaled voltage and dividing by 60 (ignoring the y intercept). Also the T2 with fan is more sensitive than without the fan.

Next I will post the mechanical details of how I added the fan.

Comments and criticisms welcome!

This entry was posted in Uncategorized and tagged , , , , , . Bookmark the permalink.

4 Responses to Calibrating the Shinyei PPD Sensors…..Part 2

  1. Stephan says:


    thanks for your research. Please post the fan modification, will this work for the PPD42NS as well?


  2. enetnut says:

    Hi Stephan,

    I will be posting my fan mods this weekend. And yes this will also work with the PPD42NS.


  3. gianluca says:

    hi, do you know where I can buy the Shinyei PPD60PV-T2 sensor? I can’t find it online…

  4. Alex says:

    Good question from Gianluca 😉

Leave a Reply to enetnut Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s